H8042CF-12 AKTIVATECH Unmanaged Industrial PoE+ Switch 5x RJ-45 10/100/1000BaseT(X), 4x Gigabit 30W PSE port 2x SFP 100/1000M BaseX, 2x SFP
- 5-Port Gigabit Ethernet PoE+
- 2x Gigabit SFP unmanaged Industrial DIN-Rail Switch
- 4x Gigabit 30W PSE port
- Operating temp.: -40 to +75 °C Wide Range Temperature
- EN50155 Certified, DIN-Rail, Wall-Mount
Specification
|
IEEE Standard |
IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3z 1000Base-X Gigabit Ethernet IEEE802.3x Flow Control and Back Pressure IEEE802.3af PoE IEEE802.3at PoE+ |
|
|
Switch Architecture |
Back-plane (Switching Fabric): 12Gbps |
|
|
Data Processing |
Store and Forward |
|
|
Flow Control |
IEEE 802.3x Flow Control and Back Pressure |
|
|
Jumbo Frame |
9KB |
|
|
MAC Address Table Size |
1K |
|
|
Packet Buffer Size |
1Mbits |
|
|
Network Connector |
5 x RJ-45 10/100/1000BaseT(X) auto negotiation, 4 x Gigabit 30W PSE
port Auto MDI/MDI-X function, Full/Half duplex |
|
|
Network Cable |
UTP/STP Cat.5e or above Cable |
|
|
EIA/TIA-568 (100m) |
||
|
Protocol |
CSMA/CD |
|
|
LED |
PW1(Power 1) Green PW2(Power 2) Green ON: Power is detected OFF: Power is not detected ERR(Relay) Amber ON – Only one power (PW1 or PW2) is connected OFF – Both PW1 and PW2 are connected |
|
|
TX/RJ-45 port: P1~P4(PoE) Green ON: PD is detected on designated port OFF: No PD is detected LNK (Link/Active) Green ON: TX port is detected Flashing: TX data is transmitting/receiving SPD(Speed) Amber ON: 1000M speed is detected OFF: 10/100M speed is detected |
||
|
SFP Fiber Per port: F5/F6 Green ON: FX port is detected Flashing: FX data is transmitting/receiving |
|
DIP Switch |
DIP 1: F5: Port F5 SFP on (Default) T5: Port T5 TX on DIP 2: 1000M: SFP 1000M (Default) 100M: SFP 100M |
|
Reserve Polarity Protection |
Present |
|
Overload Current Protection |
Present |
|
Power Supply |
Redundant Dual DC 12V-56V Power Input |
|
Alarm Relay Contact |
Relay outputs with current carrying capacity of 1 A @24VDC Relay in short circuit mode when 2 powers are connected. In open circuit mode when only one power supply is connected |
|
Power Consumption |
5.76W@12/24/48 VDC full load, Without PoE |
|
PoE power |
PoE power per port 30watts. Maximum total power 60W at 12VDC power input, Maximum total power 120Watts at 24VDC and 48VDC power input. |
|
Removable Terminal Block |
Provide 2 Redundant power, Alarm relay contact ,6 Pin Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire (AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm |
|
Operating Temperature |
-40°C~75°C fully tested. |
|
Operating Humidity |
5% to 95% (Non-condensing) |
|
Storage Temperature |
-40°C~85°C |
|
MTBF (mean time between failure) |
693764.32hrs (Telcordia (Bellcore), GB) at 50°C |
|
Housing |
Rugged Metal + Aluminum heat sink, IP30 Protection |
|
Case Dimension (LxWxD) |
142 x 42.8 x 105 mm (L x W x D) |
|
Installation |
DIN Rail or Wall Mount |
|
Certifications |
|
|
Safety |
LVD(EN62368-1) |
|
EMC/EMS |
CE, FCC, EN55032/EN55035, VCCI |
|
EMI |
FCC Part 15 Subpart B Class A |
|
Vibration |
EN 60068-2-6 |
|
Shock |
EN 60068-2-27 |
|
Free Fall |
EN 60068-2-32 |
|
Railroad |
EN50155 / EN50121-3-2 |
|
Railroad |
EN50155 / EN50121-4 |